Bimetal Type Steam Trap (GABK67/CS67H)

Product Description

Bimetal Type Steam Trap (GABK67/CS67H)

Product Description

Product: Bimetallic  steam trap
Pressure Rating: 1.6- 4.0Mpa
Specification: Screwed:DN15-50, Flanged:DN15-50
Material: cast steel
Standard flanges: DIN, ANSI, JIS; Standard screwed: NPT BSP

Our Advantages

Performance / Advantages: 

Adopt imported material as its hot sensitive element, and so it is high sensitivity and longtime useful life.
There is condensation water in front of valve for forming water-seal, no fresh steam leakage.
Good exhaust, water hammer resistance and can be installed at any angle.

Advantages:
1. Bimetallic steam traps are usually compact, yet can have a large condensate capacity.
2. The valve is wide open when the steam trap is cold, giving good air venting capability and maximum condensate discharge capacity under 'start-up' conditions.
3. As condensate tends to drain freely from the outlet, this type of steam trap will not freeze up when working in an exposed position. The bodies of some bimetallic steam traps are designed in such a way that they will not receive any damage even if freezing does occur.
4. Bimetallic steam traps are usually able to withstand water hammer, corrosive condensate, and high steam pressures.
5. The bi metal elements can work over a wide range of steam pressures without any need for a change in the size of the valve orifice.
6. If the valve is on the downstream side of the seat, it will tend to resist reverse flow through the steam trap. However, if there is any possibility of reverse flow, a separate check valve should be fitted downstream of the trap.
7. As condensate is discharged at varying temperatures below saturation temperature and, provided water logging of the steam space can be tolerated, some of the enthalpy of saturated water can be transferred to the plant. This extracts the maximum energy from the condensate before it drains to waste, and explains why these traps are used on tracer lines where condensate is often dumped to waste.
8.Maintenance of this type of steam trap presents few problems, as the internals can be replaced without removing the trap body from the line.
   The flash steam produced whenever condensate is discharged from a higher to a lower pressure will tend to cause an increase in back pressure in the condensate line. The cooling leg allows the condensate to cool down, producing less flash steam in the condensate line and thus helping to reduce the back pressure.

Working Principle

Working Principle: 

By the deformation of bimetallic strip caused by the change of temperature, drive the valve plug for opening and closing the valve seat hole, realizing stopping steam and drain.

Main Basis for Type Selection: 

Condensation water loading (discharge)kg/h (select the multiplying power 2-3 times).
Maximum working pressure Mpa
Operation pressure differential
Valve material and nominal pressure
Connection mode and dimension
 
Use and Maintenance: 
Confirm the valve material, pressure and check if the maximum is suitable for operation condition.
Before installation, clean the pipeline and clear away sundries.
The installation position shall be closed to heating equipment as much as possible.
Install the minimum point of pipe horizontally and the direction of flow should be the same to the label of valve.
Install steam trap for each heating equipment in case cause influence each other.
under the safe operation of system, open the valve in front of the steam trap, make it rise up to normal station slowly.
Do time-based maintenance for the normal working of steam trap.

Product Details

Product Parameters

Performance Parameter/ Material List of Main Part:

Working Pressure Range	0.05~1.6Mpa	Allowable maximum temperature	325
Valve body, valve cap	WCB / 304	Hot sensitive element	Import bimetallic
Valve seat	2Cr13 / 304	Screen	Stainless Steel

 

Product model	DN	Conjunction method	Max.allowable temp.	Material of valve body	External dimension (mm)
					L	H1	H2	A
BK TYPE Bimetallic  steam trap	15	Flange	220	WCB	150	100	22.0	85
	20	Flange	220	WCB	150	100	22.0	85
	25	Flange	220	WCB	160	100	22.0	85
	32	Flange	220	WCB	200	140	39	-
	40	Flange	220	WCB	200	140	39	-
	50	Flange	220	WCB	230	140	39	-
BK TYPE Bimetallic  steam trap	15	Internal thread	220	WCB	95	100	22.0	85
	20	Internal thread	220	WCB	95	100	22.0	85
	25	Internal thread	220	WCB	95	100	22.0	85
	32	Internal thread	220	WCB	200	140	39	-
	40	Internal thread	220	WCB	200	140	39	-
	50	Internal thread	220	WCB	230	140	39	-
BK TYPE Bimetallic  steam trap	15	Socket welded	220	WCB	95	100	22.0	85
	20	Socket welded	220	WCB	95	100	22.0	85
	25	Socket welded	220	WCB	95	100	22.0	85
	32	Socket welded	220	WCB	200	140	39	-
	40	Socket welded	220	WCB	200	140	39	-
	50	Socket welded	220	WCB	230	140	39	-

View of the factory

   

Product Photo

Packaging & Shipping